Product description

 

 

IE2 Electric Motors

 

 

 IE2 Electric Motors

 IE2 Electric Motors

Get more specifications

>>IE2 catalogues

>>IE2 motor manual

>>IEC directive

>>Go to checkout

 

General info about our IE2 motors

Asynchronous low voltage three-phase Hoyer IE2 IEC TEFV Squirrel-Cage Motors Type HMA2 (aluminum) and HMC2 (cast iron).

Hoyer IE2 Electric Motors are manufactured according to the efficiency class system specified under IEC 60034-30 and are installed in many different industrial fields all over the world. With a proven quality, high reliability and performance, Hoyer IE2 is a known brand in the market.


Technical info

Hoyer IE2 Motors are supplied in HMC2 type cast iron execution from frame size 160 to 400. All Hoyer IE2 Motors in cast iron are provided with SKF bearings, 3xPTC in windings. Hoyer IE2 Motors from frame size
56 to 132 are supplied in HMA2 type aluminum with C&U bearings.

Hoyer IE2 HMC2 Motors are provided with metal cable glands for main supply. Connection for accessories are provided with M20 metal blind caps.

Hoyer IE2 HMA2 Motors are provided with plastic cable glands for main supply. Connection for accessories are provided with M20 plastic blind caps.

400V Y – Hoyer IE2 Motors ≤ 3 kW
400V D – Hoyer IE2 Motors ≥ 3 kW


Application info

Hoyer IE2 Electric Motors are used within a wide variety of applications. Below we have listed some of the typical applications: 

  • Fans (air handling units, refrigeration plants, oil coolers)
  • Hydraulic power packs
  • Pumps (for water, fuels, oils)
  • Shredders (granulation, crushing)
  • Gears (gear reducers, gearmotors)

Accessories

Accessories such as heating element, klixon, IP56 and IP65 can be attached to all of our electro motors. The accessories ca be selected for each product when ordering. The additional cost is clearly stated before the final order.

 

 

 

 IE3 Electric Motors

 

 

 

 

 IE3 Electric Motors

 

 

 

Get more specifications

>>IE3 catalogues

>>IE3 motor manual

>>IEC directive

>>Go to checkout

 

General info about our IE3 motors

Asynchronous low voltage three-phase Hoyer IE3 IEC TEFV Squirrel-Cage Motors Type HMA3 (aluminum) and HMC3 (cast iron).

Hoyer IE3 Electric Motors are manufactured according to the efficiency class system specified under IEC 60034-30 (See the EC directive here). With a proven quality, high reliability and performance, Hoyer IE3 is the Electrical Motor of the future.

Technical info

Hoyer IE3 Motors are supplied in HMC3 type cast iron execution from frame size 160 to 400. All Hoyer IE3 Motors in cast iron are provided with SKF bearings, 3xPTC in windings. Hoyer IE3 Motors from frame size 56 to 132 are supplied in HMA3type aluminium with C&U bearings and 3xPTC in windings. Motors in size ≤ 180 are with closed bearings greased for life.

Hoyer IE3 HMA3 and HMC3 Motors are provided with blind caps in all supply connections.

All Hoyer IE3 Motors are as standard IP55, prepared for drain holes and painted RAL 9005 low gloss.

400V Y – Hoyer IE3 Motors ≤ 3 kW
400V D – Hoyer IE3 Motors ≥ 3 kW

Application info

Hoyer IE3 Electric Motors are used within a wide variety of applications. Below we have listed some of the typical applications:

  • Fans (airhandling units, refrigeration plants, oil coolers)
  • Hydraulic power packs
  • Pumps (for water, fuels, oils)
  • Shredders (granulation, crushing)
  • Gears (gear reducers, gearmotors)

Accessories

Accessories such as heating element, klixon, IP56 and IP65 can be attached to all of our electro motors. The accessories ca be selected for each product when ordering. The additional cost is clearly stated before the final order.

 

 

 

Hoyer ATEX zone 22 Electric Motors

 

 

ATEX ZONE 22 Electric Motors

ATEX ZONE 22 Electric Motors

 

 

Get more specifications

>>EC directive data

>>Go to checkout

 

General info about our ATEX motors

Hoyer ATEX zone 22 Electric Motor is certified for Hoyer by NEMKO.Asynchronous low voltage three-phase IE1, IE2 and IE3 Hoyer ATEX zone 22 IEC TEFV Squirrel-Cage Motors Type MS, HMA2, HMA3 (aluminum) and Y2E2, HMC2, HMC3 (cast iron).

Hoyer ATEX zone 22 Electric Motors are installed in many different industrial fields all over the world. With a proven quality, high reliability and performance, Hoyer ATEX zone 22 is a known brand in the market.


Technical info

Hoyer ATEX zone 22 Electric Motors are supplied in cast iron execution from frame size 160 to 400. All Hoyer ATEX zone 22 Electric Motors in cast iron are provided with SKF bearings and 3xPTC in windings. The electric motors from frame size 56 to 132 in aluminum are with C&U bearings.

Hoyer ATEX zone 22 Motors are provided without cable glands for main supply, however with blind caps mounted. Connection for accessories are provided with blind caps.

400V Y – Hoyer ATEX zone 22 Motors ≤ 3 kW
400V D – Hoyer ATEX zone 22 Motors ≥ 3 kW

Notice for the use of electrical equipment in areas with combustible dust.

Designation of motor according to EC directive:

  • Ex II 3D T120°C, IP55
  • The dust hazardous 3-phase asynchronous motors are in accordance with European standard EN 50281-1-1
  • Combustible dust areas will be found in agricultural areas and in industrial environments
  • Only one electrical installation may be installed in one specified area (zone)
  • Only certificated cable glands for category 2D may be used
  • Unused glands must be closed
  • Connections must be made in such a way as to ensure that a permanently safe electrical connection is maintained, both for the main supply and earth connection
  • Installations must be in accordance with actual standards for installation in the Zone 22 area
  • It is recommended that EN 50281-2 is followed according to temperature and dust on the motor surface
  • The use of motors with so much surface dust that the motor temperature increases is not permitted
  • Regularly cleaning is recommended
  • The radial shaft sealing ring is part of the ATEX certification. It is important that the ring is always intact
  • The shaft sealing must be regularly checked, and if dry it must be lubricated. It is recommended that the seal is re-lubricated regularly
  • Always use the original seal ring when replaced. Replacing bearings also means replacing the seals
  • All machines must be inspected regularly for mechanical damage
  • The user is responsible for changing parts in accordance with the lifetime of parts, in particular: bearings, grease and lubrication of shaft sealing
  • Maintenance, repairs and replacement on zone 22 motors must only be carried out by qualified specialists


Application info

Hoyer ATEX zone 22 Electric Motors are used within a wide variety of applications. Below we have listed some of the typical applications:

  • Fans (air handling units, refrigeration plants, oil coolers)
  • Hydraulic power packs
  • Pumps (for water, fuels, oils)
  • Shredders (granulation, crushing)
  • Compressors
  • Gears (gear reducers, gearmotors)

 

 

 

 V-belts

 

 

 

V-belts

Get more specifications

>>V-belts catalogues

>>Contact us for booking

 

General info about our V-belts

We are proud to provide a complete product range in V-Belts from TEXROPE®, in both covered and Raw-edge execution. We stock a wide range of V-ribbed belts, wide belts, variable-speed drive belts and multiple V-belts.

  • Classical section V-belts: Z, A, B, C profiles
  • Narrow V-belts: SPZ, SPA, SPB, SPC, XPZ, XPA, XPB, XPC
  • V-ribbed belts in: PJ, PL, PM

Material

The belts are supplied in:

  • Rubber  

Details

All standard lengths and widths are available from stock.

Standards

The belts are manufactured in compliance with applicable ISO and DIN standards. The belts are supplied as tolerance stable and anti-static (ISO 1813).

Typical applications

The belts can be used to power transmission, as conveyor belts, in industrial applications, agriculture, etc.

 

 

 

V-belt pulleys

 

 

  

V-belt pulleys for taperlock

Get more specifications

>>V-belts pulleys catalogues

>>Contact us for booking

 

General information about our Pulleys

We stock standard sizes of the following V-belt pulleys for taper bushes for Z, A, B, C, SPZ, SPA, SPB, SPC belts. The pulleys are available as standard in cast iron and are also produced in standard steel and stainless steel.

Material

The pulleys are supplied in GG25

Details

We has an extensive inventory of V-belt pulleys for taper bushes. Standard profiles SPZ, SPA, SPB and SPC are available, and depending on the profile can be delivered with 1 to 10 grooves. Sizes vary from 56-1250 mm. in diameter. 

Standards

The pulleys are produced in accordance with applicable ISO and DIN standards. All pulleys are available in material GG25. Static balanced according to Q 6.3 and manufactured according to ISO 4183, DIN 2211 /1. 

Typical applications

The pulleys can be used for, industry, agriculture, marine industry and others, for example:

  • Fans
  • Pumps
  • Presses
  • Generators
  • Crushers

 

 

 

Taperlock bushes

 

 

 Hoyer taperlock bushes and hubs

Get more specifications

>>Taperlock bushes catalogues

>>Contact us for booking

 

General information about our Taberlock bushes 

Taperlock bushes, timing belt pulleys, etc.

  • Stocked from size 1008 to size 6050 

Material

Bushes made of steel or GG25 and stainless steel upon request. 

Details

Time saving and easy mounting.

Standards

All taper lock bushes are manufactured according to current standards. 

Typical applications

The bushes are used in industry, for easier mounting and dismounting of sprockets and pulleys on shafts, as well as easy alignment etc. The bushes are also suitable for reuse, i.e. several mountings and dismountings.